Уважаемые коллеги, доброго времени суток! Представляем вам Steel and Composite Structures - научное издание из Южной Кореи. Журнал имеет первый квартиль, издается в Techno Press, его SJR за 2020 г. равен 1,048, импакт-фактор - 5,733, печатный ISSN - 1229-9367, электронный - 1598-6233, предметные области - Строительно-монтажное проектирование, Металлы и сплавы, Строительство зданий и сооружений. Вот так выглядит обложка:
Редактором является Чанг-Кун Чои, контактные данные - cck@kaist.ac.kr, info@techno-press.com.
Данный международный журнал является ценным источником для публикаций, в котором сообщается о последних исследованиях в области стальных конструкций и сталебетонных композитных конструкций, а также конструкций с покрытием из стеклопластика от международного сталелитейного сообщества. Результаты исследований, представленные в данном журнале, касаются всех аспектов теоретических и экспериментальных исследований, включая коробление/устойчивость, усталость/разрушение, огнестойкость, соединения, рамы/мосты, пластины/оболочки, композитные конструкционные компоненты, гибридные конструкции, изготовление/техническое обслуживание, Нормы проектирования, динамика/вибрация, конструкции из цветных металлов, неметаллические пластины, аналитические методы. Журнал специально стремится преодолеть разрыв между теоретическими разработками и практическими приложениями в интересах как ученых-исследователей, так и практикующих инженеров. В данном свете особенно приветствуются статьи практикующих инженеров.
Адрес издания - http://www.techno-press.org/?journal=scs
Пример статьи, название - Optimum arrangement of stiffener on the buckling behaviour of stiffened composite panels with reinforced elliptical cutouts subjected to non-uniform edge load. Заголовок (Abstract) - Cutouts in the beams or plates are often unavoidable due to inspection, maintenance, ventilation, structural aesthetics purpose, and sometimes to lighten the structures. Therefore, there will be a substantial reduction in the strength of the structure due to the introduction of the cutouts. However, these cutouts can be reinforced with the different patterns of ribs (stiffener) to enhance the strength of the structure. The present study highlights the influence of the elliptical cutout reinforced with a different pattern of ribs on the stability performance of such stiffened composite panels subjected to non-uniform edge loads by employing the Finite element (FE) technique. In the present formulation, a 9-noded heterosis element is used to model the skin, and a 3-noded isoparametric beam element is used to simulate the rib that is attached around a cutout in different patterns. The displacement compatibility condition is employed between the plate and stiffener, and arbitrary orientations are taken care by introducing respective transformation matrices. The effect of shear deformation and rotary inertia are incorporated in the formulation. A new mesh configuration is developed to house the attached ribs around an elliptical cutout with different patterns. Initially, a study is performed on the panels with different stiffener schemes for various ply orientations and for different stiffener depth to width ratios (ds/bs) to determine an optimal stiffener configuration. Further, various parametric studies are conducted on an obtained optimal stiffened panel to understand the effect of cutout size, cutout orientation, panel aspect ratio, and boundary conditions. Finally, from the analysis, it can be observed that the arrangement of the stiffener attached to a panel has a major impact on the buckling capacity of the stiffened panel. The stiffener. Key Words: 9-noded heterosis element; buckling; composite laminates; elliptical cutout; finite element method; nonuniform edge loads; reinforced cuto