Not all injection vehicle owners, especially new drivers, will be able to rinse injectors and clean injectors on their own. But, before you start this procedure, you need to understand whether it is possible to clean the injectors and rinse the injector without the help of car service, or still without a trip to the service station can not do. It depends on different factors, but most often the independent cleaning of injectors and injector is not a global problem.
For independent performance of this procedure requires certain training, basic knowledge of the design and operation of your car, so that during maintenance not to make gross mistakes. It is also necessary to have certain devices, chemicals and tools, consult with professionals, carefully study the manual on the car, to chemical reagents for washing. Only after that you can start working. Nozzle cleaning has recently become very popular. The incentive for independent maintenance of your own machine was the high price for this type of work. The desire to save money leads to different methods of cleaning the injector and injectors, as opposed to visiting car repair services.
However, incorrect performance of fuel system cleaning can lead to malfunctions of the injection system and the need to purchase new injectors, which cost a lot of money. When cleaning the injectors, the Injector in the vehicle is a pressurized fuel injection system. It is a complex device that includes, in addition to the electric fuel pump, pressure regulators, a control system, various sensors that measure the properties of fuel, inlet manifold and other elements. A serious disadvantage of the injection power system is its rapid clogging and loss of efficiency due to the use of low quality fuel. In this case, there is the problem of nozzle cleaning.
Cleaning and flushing of the injector should be carried out at the distance of more than 20 thousand km, depending on the fuel used and the peculiarities of the system design. Signs of injector contamination Dirty candles. Starting the engine is harder than usual. The engine does not run smoothly when idling. Smoke exhaust from the muffler. The engine does not develop maximum power. If we consider the reasons for the reduced efficiency of the engine, there are many of them. Therefore, it is often doubtful whether the injector is to blame for poor engine performance. If you have not had enough experience in this area, it is advisable to visit a workshop. Nozzle washer chemicals There are a variety of washer fluids available for cleaning the injector, which need to be carefully selected without saving on cheap counterfeit products.
If the choice is wrong, a new set of nozzles will have to be purchased and the savings will be a thing of the past. The most popular liquid for injector cleaning was imported Wynn's brand cleaner. It is considered strong. Vince's product is well suited for heavy dirt injector, and in the combustion chamber and on the valves appeared carbon deposits. This chemical agent is recommended for use in older cars. Vince is not recommended or even prohibited for new modern cars. When using it in new cars you will have to change spark plugs and make other unplanned expenses. Import reagent Liquid Molly saves candles, and there will be no need to change them. However, this liquid is not suitable for cleaning the carbon residue on the valves. The advantage of Liquid Molly is its versatile use, and weak effect on the nozzles. Laurel flushing fluid by the nature of the action on the injection system is similar to the liquid Vince. But it has a high cost, because of which it is little used as a beginner and professional craftsmen. The automotive chemical market offers a large number of fluid grades for flushing the injection system. Therefore, it is important to make the right choice of means. Injector cleaning equipment.
The most modern equipment for the maintenance of the injector engine injection system is a flushing stand. It is factory-built and is usually used in service stations and car repair shops. The cost of such equipment is very high and hardly suitable for individual applications. It is possible to make an injector flushing device without removing the injectors from the materials on hand. Materials for the homemade device Rubber hose with a length of 2 meters. Two litre plastic bottle. Tubeless tire nipples 2 pcs. Fluid pump with pressure gauge. Hose clamps 4 pcs. Pieces of wire, terminals, etc. The attachment from such elements will turn out simple enough, but it sometimes works not worse than the factory equipment. You can buy a ready-made device or ask your friends for it.
To be continued in the next part...